9 Things You Can Do With Bar Keepers Friend

Table of Contents

In Indianapolis, Indiana, in 1882, it can do much more than clean and polish brass hardware fixtures — the job it was originally marketed to do.

What Are the Ingredients in Bar Keepers Friend?

Bar Keepers Friend's seemingly magical properties can be attributed to its primary ingredient, oxalic acid. This natural compound targets and breaks down rust, lime, tarnish, and other stains on a molecular level, effectively eliminating all evidence of them. Fortunately, it can be used on a variety of surfaces.

.

You can’t afford not to utilize its cleaning power!

- Automobile glass and certain aluminum or chrome parts.

Our cleaning specialists recommend combining the powder with water to form a paste, and then wiping it off after a short amount of time. Prolonged contact may harm finishes.

According to Homer, to clean effectively, mix 1/4 cup of BKF powder with some water to create a thick paste. Apply the paste to the surface, let it sit for 10 minutes, allowing the acidic properties to penetrate and loosen dirt. Then, scrub the area with a gentle touch.

The manufacturer recommends not using BKF on surfaces that are porous, which include cast iron, granite, marble, wood, fabric, leather, or any surface that has been painted.

* Cover the grout with a thin layer and scrub in well, rinsing off when complete

Always test a new product, including corrosive agents, in a hidden area first.

Clean the bathroom surfaces and fixtures.

The Grout Off formula can be used to clean grout, as well as common areas such as toilets, showers,

She says, "Flush the toilet and lower the water level in the tank by pushing down the flush valve." "Sprinkle the cleaner on the stain, spread it around with a brush, wait 10 minutes, and then scrub it."

Note: For severe rust, consider applying a rust-resistant primer before painting.

Apply a paste directly to the problem area, let it sit for a minute, then wipe it away. This is effective on various items in your garage, such as golf clubs, garden tools, ice skate blades, and old bicycles.

Use a cotton swab to clean hard-to-reach areas. “I rescued a dirty old classic Radio Flyer tricycle with rusty handlebars from the landfill using just a can of Bar Keepers Friend and the back of a kitchen sponge,” says Homer. “It was looking like it just rolled off the factory floor in under 20 minutes.”

Remove adhesive labels

To effectively remove the adhesive and unwanted residue from labels, simply spray the product on the area, let it sit for about a minute, and then wipe clean.

Renew a fireplace

Remove the insert and lay the glass flat. Wet the glass and sprinkle with BFK. Wait 15 to 20 seconds, then lightly scrub the glass with a wet sponge. Rinse and repeat until the glass sparkles.

Clean kitchen surfaces

Use a gentle, non-abrasive sponge, cleaning in the direction of the grain.

First, remove any food particles from the area. Next, apply a dish soap or cleaner to the affected area and let it sit for up to five minutes. Dampen a sponge, then apply Cooktop Cleaner to the sponge by rubbing it on the soap. Use the sponge to gently wipe the stained area in a circular motion. Finally, rinse the sponge well and wipe away any remaining cleaner from the cooktop.

Scour siding

Clean the siding with a mixture of Bar Keepers Friend and water. Soak a section with water, then scrub the area lightly with a damp sponge by working the solution into the siding. Afterward, thoroughly rinse the area with clean water.

Detail your vehicle

Wipe down clear and dry, then dampen. Sprinkle with BKF. Gently scrub, let sit for up to a minute, then rinse with warm water. Repeat until sparkling.

Update dishes

To remove scratches on dishes, mugs, and servingware, apply BKF to a damp sponge, then gently rub it onto the scratched area. Let it sit for 10 to 15 seconds. After that, scrub the area lightly with the same damp sponge. Finally, rinse and dry the surface.

Refresh sneakers

To clean your shoes, make a paste with baking soda and water, and scrub all non-leather surfaces. Use a toothbrush to get into tight spaces on the rubber soles and edges. Continue scrubbing until the shoes are clean, then use a damp sponge to wipe away any remaining paste.